Why are Copper Seals Crucial in High-Temperature Settings?

There’s a reason some materials are repeatedly selected to deal with increased heat in a system. Some materials can be very unreliable. Selecting a dependable material to deal with thermal stress can provide a system that operates reliably and effectively and can save money by avoiding system outages.

What Makes Copper the Right Choice?

Copper has a long history in engineering. Knowledge of the ways Copper behaves in sealing applications and Copper’s behaviour as a conductor of heat makes Copper a beneficial engineering material. Unlike other materials Copper conducts heat to other parts of the system, which helps decrease the concentration of thermal stress in a system.

Copper is also malleable and, under sufficient pressure, will deform slightly to provide a barrier. This is important when paired surfaces are not perfectly smooth, and any gap would present a potential leak. Copper Seals can be used in a variety of applications, flanged connections, cylinder heads, and exhaust systems. Copper Seals are also used in the automotive, oil and gas, hydraulics, and industrial manufacturing industries. The expectation of each application is similar: other materials will fail where Copper Seals are expected to succeed.

Temperature Resistance: Where Other Materials Fall Short

Rubber and polymer gaskets can’t be exposed to high heat. Many elastomers start to¹ significantly degrade at temperatures exceeding 200ºC. With continuous exposure, they become hard, fissured, and permanently compressed, losing their ability to seal.

Metals, especially copper, perform much better. The melting point of copper is 1,085ºC and in sealing applications, copper can withstand continual thermal cycling in engine bays, boiler circuits, or pressurised hydraulic circuits.

Performance of copper is better than softening elastomers, which start losing their sealing effectiveness and sealing function below 200ºC after extended use.

Corrosion and Chemical Resistance

Most heated gases and liquids are corrosive. In many industrial applications, seals are exposed to oils, fuels, hydraulic fluids, steam, and the chemical processes involved in manufacturing. Copper also does well in many of these situations, especially when used in composite seal design, or coating/plating.

In combustion and exhaust applications, seals can face multiple cycles of thermal shock corrosion and contact with particulate residue and combustion gases. The ability of copper to retain its shape and surface contact is one of the reasons it’s used in engine re-build kits and performance applications.

Copper is susceptible to corrosion from continuous contact with acid or ammonia. While it is still important to identify the right type of seal copper for the environment, in some cases, oxygen-free copper or maybe more appropriate for ammonia than the regular commercial grade copper.

Things to Consider

You should know some of the factors because this might be your first time purchasing copper seals.

The size of the copper seal must be taken into consideration. If the copper seal is of the wrong size, it will either not seal at all and leak or it can be damaging to the part it will seal.

Copper can fill spaces but should not be relied on. Good seal surfaces should be undamaged, and the flanges should be inspected and cleaned to ensure there are no foreign materials on the sealing surfaces.

You should not torque copper seals to arbitrary values. If torqued much more than it should be, seals will be extruded; but if it is torqued much less than it should be, it will result in an uncompressed seal. Follow the instructions and always use a calibrated torque wrench to set the seal to the recommended value.

A Reliable Choice When the Situation is Difficult

Copper Seals are one of the few well-founded, affordable options for sealing joints exposed to heat, pressure, and mechanical stress. Their requirements are few and are easily satisfied by the correct sizing and cleanliness of the joints, and the appropriate treatment. Their longevity, reliability, and resistance to the conditions which quickly corrode inferior materials, make them an excellent choice.

Whether the copper is for engine rebuilds, repair of factory piping, or even supply for new construction, it is a material that warrants understanding before it is chosen.

How do you store long items

There is a specific problem that manifests itself in warehouses, builders’ merchants, and metal stockholders, for which there does not seem to be a clear solution until you witness it being done correctly. How do you store long items such as timber, steel sections, pipes, or aluminium extrusions without occupying vast amounts of floor space or creating a messy tangle that makes retrieval a logistical nightmare?

The solution is in front of you in every industrial facility in the country, yet most people outside these industries have not consciously ever noticed it. And so… cantilever racking is the solution to a spatial problem that normal shelving cannot address.

Why Normal Racking Fails

Normal pallet racking is perfect for boxes, crates, and anything else that can easily be placed on a pallet. The vertical uprights at regular intervals provide the structural support for the shelving, and forklifts can slide in and out between these uprights. However, how do you store 6-metre sections of timber or steel bars on this type of shelving? The problem is that the uprights are in the way. You cannot slide the timber in horizontally because of the vertical supports. Nor can you store these items vertically because it wastes the full height of the building, plus it is a logistical nightmare because no-one wants to have to manipulate 6-metre steel bars at awkward angles near the ceiling. And laying the items flat on the floor is okay until you need the item at the bottom of the pile, in which case you have to shift everything else first.

Cantilever racking systems do not have any front uprights. Instead, the arms are fixed out from a central spine. This provides unobstructed space for storing materials horizontally and accessing them directly. It is a very clever design. The entire weight is distributed via the cantilevered arms back to the base and column. The base and column have to be very heavy and robust to resist the forces of leverage.

The Physics That Make It Work

The physics behind a cantilever racking system are exactly the same as if you were holding out your arm straight and holding a heavy object in your hand. The farther out your hand is from your body, the heavier the object will feel. The actual weight of the object will not have changed, but the leverage will have. The same is true of a cantilevered racking system. The farther out the object is from the column and the base of the racking system, the heavier it will be. The base of a cantilever racking system is usually very heavy compared to the thinness of the cantilevered arms.

Engineers have to calculate the safe weight capacity of a cantilever racking system based on the actual weight of the object and the distance of the object from the column and the cantilevered arm. A 500kg object will have very different stresses on a 1-meter cantilevered arm compared to an object that is closer to the column. The actual specifications are important. Otherwise, the cantilevered arm will end up bent or the entire structure will collapse.

The base of a cantilever racking system is very important. In permanent installations, these systems are bolted into concrete floors. The last thing anyone wants is a cantilevered racking system tipping over due to its own weight. Some systems use a counterweight base instead of a fixed base. This is a heavy object that is positioned on the base of the racking system and acts like a platform.

Variations for Different Materials

Single-sided cantilever rack storage is best used against the wall or when access is only needed from one direction. Double-sided cantilever rack storage maximizes space efficiency in open areas, with arms on both sides of the storage column. Products can be stored on both sides with different product categories or the same product category on both sides.

Arm sizes can differ substantially. For light-duty applications with items such as plumbing fixtures or smaller sections of timber, the arms might be relatively narrow, perhaps only 40 to 60mm thick. Heavy-duty applications with structural steel sections or large diameter pipes might feature arms 100mm or more in depth.

Height configurations can also differ substantially. Depending on the building and the equipment used to access the storage, low-level configurations might only reach 2 to 3 meters high. Larger configurations can reach 6 meters or more, with the proper forklift trucks required to access the storage.

Some cantilever storage configurations feature arms that can be adjusted vertically to different positions up the storage column. While this is obviously useful, it adds further complexity to ensure the arms remain securely fixed.

What Actually Gets Stored

Construction materials such as timber in various sections, steel beams, steel pipes and tubes, plastic extrusions, and aluminium sections. But cantilever storage is useful for other purposes as well. Carpet and flooring outlets can use it to store rolls. Sheet metal fabricators can utilize it to store different gauges of sheet metal. Even furniture storage can feature cantilever storage configurations to house items such as table legs, bed frames, and other elongated items.

What they all have in common is the geometry issue. Do you have inventory items that are longer than they are wide or tall? Do you find that the storage solutions you’ve implemented cause more problems than they solve? Then cantilever storage configurations might be something to consider.

The Operational Reality

Forklift drivers must be skilled in the operation of cantilever racking systems. The process of loading and unloading these systems is not an easy task. The process of sliding a 6-meter steel piece into the cantilever requires a high level of expertise and concentration. The facility will have clear guidelines on the operational process of these systems. The damage of these racks is a frequent phenomenon. Most companies offer replacement of these racks as a standard facility. A forklift truck running into these racks while loading materials or dropping materials heavily on these racks will cause damage to these racks. The damage may cause the racks to bend or crack. The operation of these racks is also a requirement for regular inspection for any deformity and cracking around the welding points. The facility will also be checked for any signs of movement of the bases and loosening of the anchors.

The Invisible Infrastructure

Like any other infrastructure for storing materials in a facility, cantilever racking is a very efficient tool for ensuring materials are stored and retrieved efficiently. The operation of these systems is so efficient that it is not even considered until something goes wrong or until a person is required to use these systems and find them wanting. In any facility where materials are the main product being stored and transported around the facility, cantilever racking is not just a tool for storing materials but is the infrastructure that makes all other things possible.

The Unassuming Engineering Behind Rigging Screws

At their heart, a rigging screw is a device designed to modify tension in a cable or wire rope system. Turning the body causes two ends to move towards each other, bringing two end fittings closer together or farther apart, thus tightening or loosening what these two ends are attached to. Of course, this is what rigging screws are designed to do: make it possible to adjust tension once a system is in place, and make it possible to adjust tension periodically as cables stretch over time.

It is a simple yet clever design. There is a body in the middle with left-hand and right-hand threading on either side of it. Turning the body causes both ends to move towards each other at twice the rate they would have moved had there been a single thread system in place. Most rigging screws have a window on the body of the device so you can check that both threaded studs are securely attached without having to remove either one.

The types of end fittings will vary based on what you are attaching things to. Eye and eye types work well for cable loops and shackles. Jaw and jaw types work well for clevis pins. Hook and eye types work well for quick attach situations, but should not be used in situations requiring high stress usage. Fork and eye types work well when some form of rotating motion is required.

Load Ratings That Matter

The rigging screw has a Working Load Limit, not breaking strength. Now, this is a very significant difference. The Working Load Limit is a measure of the maximum loads that a piece of equipment will ever see, with a 4:1 or 5:1 safety factor built in. So, a rigging screw has a WLL of 500kg. It does not mean that it will break until you get up to 2,000-2,500kg. However, you should not get anywhere near these limits. The weak points are in the threaded connections, not in the rigging screw. Threads concentrate forces in small areas, particularly in the first few threads.

This is why thread engagement is so vital, particularly in most specifications, where there should be a minimum of 75% of the length of the threads engaged. The size of the rigging screw has a very significant impact on the rigging screw. However, it does not have a straightforward impact. If you go from a 10mm diameter rigging screw to a 12mm diameter rigging screw, it does not mean that the new screw will have a 20% increase in load rating. It will actually have a 45% increase in load rating due to the increase in area.

Installation Details That Get Overlooked

Lubrication of the threads is not often considered a significant factor in the installation of rigging screws. However, it has a significant impact on the usability of the screw in the future. Dry threads can cause problems in the future should it ever need to be adjusted. A light coating of grease or anti-seize can work wonders in the future. Marine environments have specific lubricants.

These mechanisms will differ in design, with some using jam nuts, which tighten on the body after the desired tension is achieved. Others will use lock wire, which is threaded through holes in the body and the end fittings. Split pins will be used when there is the possibility of vibration, which would cause the parts to rotate.

When Your Stock Needs to Stick Out: The Case for Double Sided Cantilever Racking

Anybody who’s ever strolled through an industrial storage facility will know that not all storage needs are created equal. And while standard pallet racking excels at storing boxes and similar items, there’s a specific problem that catches many operations managers out. This is the problem of storing long and difficult items like timber, steel beams, pipes, and aluminium profiles. And this is where double sided cantilever racking enters the equation, and let’s be honest, this is a storage solution that makes you wonder how people ever managed without it.

So What Makes It So Different?

Well, the actual design of this storage solution is quite simple to be fair. Essentially, you have a vertical pillar with horizontal protrusions on both sides, rather like a metal tree with branches extending outwards from the main pillar. This is where you place your storage items, and they can be accessed from both sides without any obstruction from pillars and posts.

The beauty of this storage solution lies in the absence of pillars and posts that plague most storage solutions and make accessing your storage items a nightmare. With this kind of storage, your forklift operators actually have room to move and can load your items quickly and stress-free.

The Space Consideration Nobody Mentions

Something else that tends to be forgotten in the early stages of planning is that a double sided cantilever racking system, in essence, offers you twice the storage space for the price of once the space. This is particularly relevant when you consider that you’re paying for commercial property space based on square footage alone.

A row of double sided cantilever racking placed down the centre of your storage space offers you twice the storage space, rather than single sided storage racks placed against the walls of your storage space, offering you only half of this.

Why Height Matters More Than You Think

Most cantilever racking solutions can be made to go quite high, and this is something that you should definitely be considering when choosing your storage space solutions.

If you’re storing items that are already several meters in length, you might as well go upwards and make full use of the space you have available to you. Most modern solutions can be made to go up to six meters or higher, so long as you have the appropriate equipment to lift your goods to these heights.

By going upwards rather than outwards, you can increase the storage space you have available to you exponentially. Rather than spreading outwards and taking up valuable space, you can go upwards and make full use of space that was otherwise going to be completely unused.

The Loading Flexibility Factor

There’s a practical advantage to these systems that you won’t realise until you have some experience with them, and that’s that you can load from either direction depending on what’s convenient at the time. That way, if one of the aisles is blocked due to other activities, you can just come at it from the other direction with your forklift.

Similarly, should you need to access items that are stored towards the centre of the rack, you’re not forced to retrieve all items from one side first. Instead, you can simply approach from the side that makes the process easiest for you, retrieve the materials you need, and continue as normal. It may seem like a small point, but it makes a big difference in terms of efficiency.

Getting the Configuration Right

The length of the arms, as well as their spacing, needs to be taken into consideration according to the materials you’re actually storing. For timber merchants, the configuration will need to be one way, for a steel stockholder another, and for a supplier of plastic pipes yet another. The load-bearing capability per arm, the distance between the levels, as well as the height, need to be matched according to your needs.

Most manufacturers offer racking systems with adjustable arm position, which can prove to be a blessing as your needs change over time. What may be perfect for you now may need adjusting in a couple of years’ time after you’ve added more items to your stock, so having that flexibility from the outset can prove to be a major cost-saver later on.

The Bottom Line

While the double-sided cantilever racking system may not be the most glamorous item you’ll ever use in the warehouse, it does solve a genuine need for many businesses that deal with long materials. It makes full use of the available floor space, offers maximum accessibility, and helps create a more efficient working environment. For any business dealing with awkward long items, it really is hard to think of a better solution.

A Factory Guide on How Cantilever Racking Works

When you are dealing with awkward and large product ranges, conventional pallet storage systems quickly prove their inadequacies. This is a situation that timber merchants, steel stock holders, and plumbing merchants will be all too familiar with. The truth is that it is extremely difficult to accommodate items such as pipes, boards, and profiles into conventional storage bays – which is where cantilever racking solutions come into their own.

“What’s Special about Cantilever Racking?”

The design itself is actually very simple. Unlike vertical frames with horizontal support beams for separate bays, the design of a cantilever system consists of a vertical post and outstretched arms. You won’t notice any interference in the form of a front post from the design, making it easy for you to move products in and out through the rack system.

The design of having an open frontage is more than just a storage facility; it actually transforms how one can effectively deal with a given type of item. The forklift truck operator can access items from all sides, and there is no need to manoeuvre to get to items which are hanging over or have to be positioned at an angle to fit between uprights.

Where It Actually Works

Generally, in the case of cantilever racking, the first thought that springs to mind will be of builders’ merchants; and in these, timber yards will be the most usual scenario. You’re obviously handling 2.4m long to 6m long products.

Notwithstanding, the applications of such shelves stretch further than the usage many people would imagine. Furniture stores utilize cantilever shelving to showcase couches and mattresses. Carpeting and flooring experts utilize the shelving to showcase the rolls of material in a way that would not be feasible in other shelving options. Manufacturing facilities utilize the shelving to showcase the material they utilize, such as metal bar stocks and plastics. Even retailers with heavy products would find the shelving useful.

Installation factors

The price will depend on a number of factors. These include arm length, weight capacity, height, and number of levels. A basic single-sided handling unit for light material handling could cost a couple of thousand pounds, but a large heavy-duty two-sided unit for a steel stockholder could cost tens of thousands of pounds.

However, such a comparison cannot and should not merely be made among different kinds of racking systems. An alternative method used for the storing of products would be the floor stacking method. Just to what extent is space wasted? Just to what extent is time spent on the retrieval of products which have to come from the floor? The level of damage caused through sub-optimal product storage strategies cannot even be quantified properly. Many times, the argument for the inclusion of a cantilever racking system may revolve around such points.

Obtaining The Correct Specification

You start by carrying out a proper stock audit. You want to measure your longest products, your heaviest products, and think about what you’ll want in the future. Businesses do grow, and you want your shelving system installation done in a way that leaves a little room for future expansion.

Partner with suppliers who ask you for information rather than those who can instantly provide you a price. Installation will go the farthest not on generalized information on how the process will help your business.

Floor surveys also contain more importance than one thinks. An uneven floor will affect not only the placement but also affect the strength of floors. The load-carrying capacity of floors may sometimes affect the entire design. A company involving expert floor installation should consider testing before finalizing specifications.

Conclusion

Cantilever racking is not suited for every warehouse, although in the cases where it can be applied, it is very effective. The trick is in identifying whether your specific warehouse problems are the right fit for this racking solution’s strengths.

It can be a truly liberating and more pleasant process, as well as ensuring greater capacity and a much safer system, when carried out well. However, when carried out badly, it’s a nightmare that’s very costly. It’s at this point that greater emphasis on specification rather than simply looking to see where to cut cost has a big impact.